TABLE OF CONTENTS

IMPORTANT PRODUCT INFORMATION: PLEASE READ THIS FIRST 

INTRODUCTION: TYPES OF PRINTERS

SECTION 1-GEN 1 PRINTER VIDEOS

(Unless otherwise noted, all videos are in .MP4 format)

SECTION 1.1- GEN 1 HOW-TO VIDEOS

SECTION 2-GEN 2 PRINTER VIDEOS

SECTION 2.1 GEN 2 HOW-TO VIDEOS

1. Capping Station Height Adjustment
2. Belt Motor Replacement
3. Encoder Strip Replacement
4. Head Replacement
5. Impact Switch Wiring
6. Rear Data Board Replacement
7. Switching to Dupont Inks

SECTION 2.2- GEN 2 MINI MANIFOLD VIDEOS

1. Mini Manifold Tank Check
2. Mini Manifold Tank Replacement

SECTION 3-PRINTER PROCEDURES (GEN 1 AND 2)

SECTION 3.1- GENERAL HOW-TO VIDEOS  (GEN 1 AND 2)

1. Adjusting Tension Knobs on Film Roll
2. Antistatic Copper Tinsel on Dryer
3. Antistatic Copper Tinsel on Printer
4. Bottom Limit Sensor Replacement
5. Flexi: Color Download
6. Flexi: (How to Nest Files)
7. Flexi: Using a PDF or Importing Spot Colors
8. Flexi: Using a PDF to Preserve Spot Colors
9. Changing a Film Roll
10. Drive Motor Replacement
11. Head Replacement Video 1
12. Head Replacement Video 2
13. Head Replacement Video 3
14. Adjusting a Color Swatch to Match Custom Colors
15. Graphics Color Match From a Pantone Chart
16. NeoStampa Use
17. UV-12 Film Help (.MOV format)

SECTION 3.2- HEAT PRESS HOW-TO VIDEOS  (GEN 1 AND 2)

1. Heat Press Electric Manual-Auto Switch
2. Power Supply Check
3. Replacing the Heat Sensor in the Lower Platen
4. Replacing the Relay Block
5. Rod Snap Ring Removal
6. Setting Max Pressure
7. Square Pin and Cylinder (.MOV format)
8. Pneumatic Cylinder Replacement

SECTION 3.3- SHAKER DRYER HOW-TO VIDEOS (GEN 1 AND 2)

1. Assembly
2. Auger Settings (.MOV format)
3. Bearing Change
4. Belt Drive (.MOV format)
5. Bulb Replacement (.MOV format)
6. Bulb Switch Check (.MOV format)
7. Dryer Demo (.MOV format)
8. Emergency Stop Button Assembly (.MOV format)
9. Emergency Stop Button Unlock (.MOV format)
10. Emergency Stop Button Assembly (.MOV format)
11. Heat Sensor Check (.MOV format)
12. Mirror Sensor Replacement Video 1
13. Mirror Sensor Replacement Video 2
14. Overall Cleaning
15. Side Doors Flipped
16. Temp Control Dip Switch (.MOV format)
17. Main Board Replacement
18. Insulation Check
19. Replacing a Digital Temp Box (.MOV format)
20. Resetting the Auger Timing Board (.MOV format)
21. Retainer Rod Device (.MOV format)

SECTION 4: DAILY AND PERIODIC PRINTER MAINTENANCE

SECTION 5: FAQs AND INFORMATIVE ARTICLES

1. CobraFlex Power and Operating Specifications
2. Where Can I Find The Material Safety Data Sheet (MSDS) for the Adhesive Powder?
3. The Proper Environment for Operating CobraFlex Printers
4. Cobraflex Electric Heat Press Instructions (No Powder System)
5. Cobraflex Electric Heat Press Instructions (Powder System)
6. General Heat Pressing Instructions
7. How Do I Activate The Flexi Cobra Addition?
8. Air Pneumatic Heat Pressing Instructions (No Powder System)
9. How Do I Adjust the Flapper and Duster Speeds on My Dryer?
10. NeoStampa10: Getting Started With the Program
11. How Do I Rip Artwork In Maintop and Open it in Well Print?
12. The Impact of Humidity on Direct-to-Film Printing
13. Is There a Way to Track How Much Film I Have Using th>e Software?
14. Humidity: Tips in Getting Powder to Stick and Adhere Correctly
15. Daily Printer Procedures and Maintenance
16. Blue Cleaning Solution (MSDS)
17. Maintaining Your Digital Printer
18. Printer Head Maintenance
19. Head Status Check
20. Head Replacement Landing Page
21. How Do I Unclog The Shaker Dryer Unit?
22. White Alignment for the Gen 1 Printer
23. White Alignment for the Gen 2 Printer
24. Ink Supply System Consumable Parts
25. Warranty
26. Washing Instructions

SECTION 6: TROUBLESHOOTING

1. Troubleshooting Landing Page
2. How to Narrow Down a Problem When Troubleshooting
3. Shaker Dryer Auger Stuck or Not Moving
4. White or Color Ink Not Printing Well
5. Disk Space Error Message
6. Film Curling
7. Film Softening
8. Prints Sticking or Peeling Off

INDEX

'